Éclairage/Décoratif/LED Guirlandes

Bande LED SmartLife

Wi-Fi | Blanc Chaud / Blanc Froid / RGB | SMD | 5.00 m | IP44 | 2700 - 6500 K | 960 lm | Android™ / IOS

Caractéristiques

Référence Constructeur: WIFILS50CRGBW
Code EAN: 5412810303106
• Facile à configurer : connectez-vous simplement à votre Wi-Fi pour configurer, contrôler et programmer cette bande de LED
• Les couleurs rouge, vert et bleu sont disponibles ou vous pouvez choisir un blanc chaud ou froid, pour correspondre parfaitement à votre humeur
• La bande peut être raccourcie ou allongée, pour des possibilités infinies
• Adhésif double face (3M) déjà en place pour une installation facile
• Fonctionne comme un éclairage intelligent autonome. Peut être couplé à d'autres produits SmartLife pour créer une maison intelligente complète
Utilisez cette bande de LED intelligente pour créer de l'ambiance dans n'importe quelle pièce. Contrôlez-la dans l'application Nedis SmartLife, définissez des horaires ou des automatisations ou utilisez vos assistants vocaux préférés pour contrôler la luminosité et la couleur de la bande LED. Elle se connecte directement à votre Wi-Fi : aucun concentrateur séparé n'est nécessaire
Cette bande de LED combinant des LED RGB et des LED blanches chaudes et froides, vous pouvez non seulement définir une couleur préférée, mais aussi l'utiliser pour un éclairage indirect blanc chaud à froid
Sa longueur de 5 mètres peut être raccourcie ou étendue avec des bandes LED similaires pour des possibilités infinies
L'adhésif double face (3M) est déjà en place, pour une installation facile sur n'importe quelle surface propre et plane.

Emballage

Contenu de l'emballage

Bande de LED RGBW (5 m)
Contrôleur Wi-Fi
Alimentation
Guide de démarrage rapide

Dimensions emballage retail Boîte cadeau avec eurolock

Largeur Hauteur Longueur
50 mm 190 mm 185 mm

Dimensions logistiques

Conditionné par Largeur Hauteur Longueur Poids
1 182 mm 50 mm 210 mm 420 g
8 195 mm 245 mm 420 mm 3720 g
32 410 mm 440 mm 510 mm 16000 g

Spécifications du produit

Largeur 151 mm
Hauteur 8 mm
Profondeur 5000 mm
Poids 310 g
Tension d'entrée 220 - 240 V AC 50/60 Hz
Gain d'antenne d'émission maximal 2.5 dBi
Compatible avec Nedis® SmartLife
Longueur du câble de l'adaptateur secteur 1.50 m
Puissance d'émission maximale 16 dBm
Indice de rendu des couleurs (Ra) 80
Couleur de lumière Blanc Froid
Blanc Chaud
RGB
Application disponible pour Android™
IOS
Classement IP IP44
Consommation électrique maximale 15 W
Fiche d'alimentation Euro (CEE 7/16)
Variable Oui
Durée de vie nominale de la lampe 20000 h
Technologie sans fil sountenu Wi-Fi
Découpable Oui
Consommation d'énergie pour 1000 heures 15 kWh
Matériau Silicone
Support de montage Monté sur la surface
Bande lumineuse extensible Oui
Plage de fréquences de transmission 2412 - 2484 MHz
Nombre de produits dans l'emballage 1 pièces
Connexion (s) d'entrée d'alimentation de l'appareil DC
Température Couleur 2700 - 6500 K
Classe énergétique F
Flux lumineux nominal 960 lm
Couleur Multicolore
Longueur de la corde 5.00 m
Type de LED SMD
Module LED SMD 5050
Nombre de leds par mètre 90 pièces

Assistance

Questions fréquemment posées

Nous avons trouvé les questions suivantes pour vous en anglais

No, the LED's are not individually addressable.

Please try the AP mode.

Make sure that you use a 2.4Ghz wifi network.

Reset the controller so the LED strip blinks slow. (press and hold the button on the controller)

If it blinks fast, reset it again and it will blink slowly



In the app:

+ > [your device] > tap on EZ mode and select AP mode > confirm it was reset > fill in the info of your wifi network > follow the steps in the app.



Hold your phone very close to the plug during the installation

This method uses a direct connection to the device to send the info of your wifi to it.

Holding it close optimises this connection

Ensure that you only take off the plastic protection and not the entire adhesive strip.
If you remove the whole strip, you will not be able to stick it to anything.

Yes, you can purchase another set and plug the second strip in the first one.
If you extend it to 10m (5m extra) then you might see some loss in brightness at the end of the second strip.
We recommend you install multiple complete sets and group them in the app.
Now you can control all of the strips as if they are a single strip without any loss in brightness.

Yes you can.
Each person needs a unique account on their mobile device.
To add them as "family members" follow these steps:
In the main screen of the app tap on the name of your home (top left)
Tap on Home management
Tap on the name of your home again.
Tap on "add family members" and fill in the account details of the person you want to add.
It will give them access to all the devices in your home as a normal member or admin (you can select this)

If you only want to share a single device in a home, go to the settings menu of the device and select "share device" -> add member.

This is probably a Wifi problem, this can be for various reasons.
1.) Wifi signal is unstable.
2.) Wifi signal is too weak.
3.) Using an access point with the same SSID and password that do not support the IEEE 802.11R standards.

Problem 1 can often be solved by restarting the router.
Problem 2 can be checked with an app Wifi analyzer with this the signal can be viewed and corrected to a better position.
Problem 3 can be checked as the access points are turned off, the Wifi signal is still good and the connection remains if the access points are a problem, a Mesh solution can then be used.
Please make sure that they support IEEE 802.11R standard.